Mini Cooper Camshaft Bolt Torque

To locate camshaft at TDC for MINI Cooper R55R56R57 2011-2015 CLICK HERE. Application Model ONE HB COOPER COOPER COOPER S SERIES R55-56 4.

Mini R50 R53 Torque Wrench Settings Mini Cooper Mini 2006 Mini Cooper

Remove the 10mm cam chain slider.

Mini cooper camshaft bolt torque. Genuine MINI Part 11128644674 11-12-8-644-674 11127613127 - Cylinder head bolt. Modified engines may also require other torque settings specific. Remove the 3 6mm bolts.

2007 Mini S Dohc 16 L Turbo Timing Chain Diagram For. The stock rod bolts have 46 lb-feet of torque and the ARP rod bolts have 50 lb-feet of torque. Using your fingers and a mini-mal amount of force pry each ring over the piston and slide it into the groove.

2AZ Main bearing bolts outer W10 W11 M8 Replace wash and oil screws 35 Nm. As a note to others. 07131487226 Mini Cooper R53 Head Bolts Mini Cooper.

About Press Copyright Contact us Creators Advertise Developers Terms Privacy Policy Safety How YouTube works Test new features Press Copyright Contact us Creators. MINI - R50-R53 - Torque Wrench Settings. Here is a PDF file over pretty much all the torque wrench settings used on a Mini.

Get more power out of your tuned MINI. To locate camshaft at TDC for MINI Cooper N12N14 2007-2011 CLICK HERE. Lucky for us BMW has made a MINI R56 timing calibration a.

Ships from Seattle MINI Seattle WA. Modified 2004 Mini Cooper S JCW 6-Speed. Remove the 2 left side cylinder bolts 5mm allen heads.

A few miles since NUT and bolt restoration. MINI factory replacement Bolt for the Adjustable Cam Sprocket on your 2nd generation MINI Cooper non-S models with the N12 or N16 engine including R56 Hardtop R55 Clubman R57 Convertible R58 Coupe R59 Roadster R60 Countryman R61 Paceman. This bolt extends through the camshaft and secures the cam-shaft cover.

Great Guide For Mini Cooper Oil Changing Socket Sizes Oil. It sheared off its mounting bolt in this 2007 MINI R56 N12 engine. This 2004 Mini Cooper S is powered by a supercharged 16L inline-four paired with.

CAMSHAFT - TIGHTENING TORQUES - COOPER 16L R50W10 1AZ - 4AZ 4AZ Timing case to crankcase M6 12 Nm. Cooper S R56 L4-16L Turbo N14 2009 Mini Workshop Manuals Engine Cooling and Exhaust Engine Camshaft Lifters and Push Rods Camshaft Engine Component Information Service and Repair 11 31 025 Removing and InstallingReplacing Inlet Camshaft Page 2338. Remove the cylinder head.

Counterhold the balancer and torque the bolt to 115Nm 85ftlbs See Figure 7 and Figure 8. Type Thread Tightening specification Measure 1AZ Main bearing bolts inner W10 W11 M10 Replace wash and oil screws 60 Nm. For locking camshaft in TDC position when checkingadjusting camshaft timing replacing inlet camshaft or timing chain.

These settings are for standard bolts nuts and fasteners used on standard Minis and Mini engines. Consult the user manufacturers recommendations for more details. 20 rows Torque lbft Torque kgm Camshaft Nut.

30 then 90degrees then 90degrees you will brake the bolts at 45 pounds on large bolts so youre smarter to go a couple posts down to get the specks Im quoting you will never get higher than 45 pounds of torque they spin for a million miles then snap at any higher torque. The torque spec for the chain guide bolts in the Bentley manual is listed incorrectly as 30 Nm. The correct torque and stretch for camshafts bolts are as follows first 20NM to hold them then after you have turned engine by hand for 4 turns and relocked the timing tools back in pace and every thing just falls in to place you can then do the rest of the tighten process which is 180 degrees or stretch for both i mark the torx bolt with tipex and watch for it to move half a turn the crankshaft bolt must be 40NM plus 120 degrees stretch and must be tightened first before camshafts.

Mini Cooper Cooper S Clubman R55 R56 R57 Service. Con Rod Big-end Bolts. Calculator Ground off restoration 1985 BMW K100 Cafe racer.

Built by one of the best K100 builders. Application for BMW N12 N14 MINI COOPER 2. Fits Clubman Convertible Countryman Hardtop John Cooper Works.

Get the tools parts. Oil Filter Housing Bolt Torque North American Motoring. According to the Mini workshop manual it should be 24 Nm for the lower.

Be sure to not let the washer fall off of this bolt into the engine. Remove the cam sprocket from inside the left of the cyl-inder head by removing the 17mm bolt. Any special bolts for example like ARP have there own torque settings and specifications.

Apply a thin. Everything is better than new. Crankshaft Main Bearing Cap Bolts Set Of 10 R555657585960 Mini Cooper.

Torque bolts to 65 ftlbs. Application Engine N12 N14 14 16 16V engine Mini cooper eingine 2007-2010 3. This is an excellent example of a MINI engine that will need its timing re-calibrated.

The crankshaft pulley has 116 lb-feet of torque while the flywheel has 80 lb-feet of torque. Note how the front exhaust camshaft sprocket VANOS is crooked. How to install a performance camshaft in a R53 supercharged MINI Cooper S.

The cylinder head studs have 70 foot-lbs of torque the cam timing gear have lb-feet of torque and the cam bearing bolt has 14 lb-feet of torque. In order to access the balancer youll need to remove the serpentine belt and also the right front wheel liner. Cooper S R56 L4-16L Turbo N14 2009 Mini Workshop Manuals Engine Cooling and Exhaust Engine Cylinder Block Assembly Harmonic Balancer - Crankshaft Pulley Component Information Technical Service Bulletins Engine - Incorrect Crankshaft Central Bolt Torque Change.

On the R55R56R57 cars the harmonic balancer is much easier to replace as it is held on to the crankshaft with only three Torx bolts. Der head cam cover by remov-ing the two 8mm bolts.